※ Download: Iso 2768 mk pdf
This link often gets put up with questions about ISO tolerance. Anyone know of a source for a simpler explaination of these that is in english? One shaft has a dim 25mm f9, a bore is marked M6 and to me that seems super tight, more than the part requires but I am hoping I just read the chart wrong.
For the required drilling diameters see page 68 and 70 , ohne Toleranzangabe nach DIN ISO 2768 m. A keyway has a N9 and the internal keyway has a j59. Erforderlicher Bohrungsdurchmesser siehe Seite 67 und 69 , on the Y-axis.
- DIMENSIONS IN MILLIMETERS - VALUES FOR INCHES IN BRACKETS - TECHNICAL DATA , tolerances are in accordance with DIN ISO 2768 m.
I have some drawings from Germany that use the DIN 2768 tolerances and I am having trouble understanding it correctly. I do not have a full copy of the DIN but I do have some notes and a brief discription of how the tolerances are supposed to work but I still dont quite understand it. The parts are shafts and couplings and have to fit bearings so I know some of the tolerances are going to be plus and some are minus. Could anyone offer a simpler explaination of what I am seeing. One of the external shafts has a f9 while most of the other shafts have a h9 or h6. A keyway has a N9 and the internal keyway has a j59. One of the internal bores has a M6. Most of the tolerances use lower case but some are upper case, I dont know if that makes a difference or not. Anyone know of a source for a simpler explaination of these that is in english? Charles A bearing catalog will have a table with the tolerances. You can also find everything you should need here at this link Basically, a small letter is the tolerance for a shaft and a captial letter is the tolerance for the hole. The M6 is the tolerance for that bore and is not a thread designation. Last edited by MBensema; 03-26-2009 at 12:53 PM. Reason: clarified info about the din 2768 i think its a standart in europe over here can give you a ling to the table with all the seizes but its a dutch chart but i cant look it up atm but basicly its 0-3mm +-0. MBensema, Thank you for that link, it doesnt offer everything I need but it does come closer than I had gotten by myself. I do have a shaft dimention that is not on the chart, it is for an OD 12mm h9. The chart skips over h9 for some reason. The other end of the shaft is 10mm h6 which should be +0,-. Charles The chart skips over h9 for some reason. This link often gets put up with questions about ISO tolerance. The same MHB, gives me a slight difference to your h6. Machtool, Yes I got that too, but there are a lot of other tolerances that are not listed in my handbook. I just need to find a better source and I am hoping to not have to buy all the standards if I dont have too. I am just quoting the job and I am still waiting on some answers from the company I got the drawings from. I thought I could get a head start and educate myself at the same time. One shaft has a dim 25mm f9, a bore is marked M6 and to me that seems super tight, more than the part requires but I am hoping I just read the chart wrong. There are keyways and snap ring grooves and I just cant seem to find all the information I was hoping for in the MHB but I will keep searching. Charles Charles, you have some weird tolerances on there, those are very rare for bearing fits. I have an ISO Tolerance book my company published, but it looks like it is not available any longer. You can find info on the DIN 2768 at the link below. Thank you, I just found the tolerances on the keyway, and no the M6 is on a 47mm bore which makes me wonder why so tight a tolerance, I was hoping I was reading it wrong. I didnt see where you got the -17 from, at least that would allow me to have a little more room to work. On the 12mm my MHB must have a typo because it says the tolerance is +43 -0? I didnt think that correct for a shaft but that is what is in my book. Now you know why I wanted to ask others, this doesnt really add up. I really do need some reference that I can point to for these just in case there is any problem I need some printed version of these tolerances. I will check out the general one you mentioned. Charles bearing tolerances are usually fairly tight since that controls the amount of internal clearance of the rolling elements to the race of the bearing when installed. An M6 tolerance on a 47mm bore should be -4 to -20 according to my book. I'm using a book published by FAG Bearings that lists the complete tolerance range for each designation, I don't have my Machinerys Handbook here to check and see what is in there. The +43 on the h9 tolerance is definitely wrong, all the h tolerances are +0 and a negative number. Are you sure you are not looking at H tolerance tables? The capital H is for holes and all of those are 0 to a plus number. After you have used it a bit, these tolerances get easier. I wish I had a copy of the complete tables I could email you, the following link is mounting and dismounting catalog that has tables in the back, but does not have all of what you are looking for. If I find some time tomorrow, I will see if I can scan my tables and send them to you. Thank you all for your help, this has been quite an education so far but it does seem to follow a pattern and I am glad I have decided to follow up with it. Your help at least lets me know where I was right and where I need to work a little harder. If anyone knows of a techical reference that might be more inclusive and useful I will gladly pay a little for the effort to copy and email or mail it to me. I was thinking of a Text book? Something some engineer in training might use or perhaps a machining student might have access to? I have several booklets on GDT and similar subjects but nothing on the european or DIN standards. Even if it was in German I could work with the tables or have one or two locals translate for me. If you want to know more or withdraw your consent to all or some of the cookies, please refer to the. By closing this banner, scrolling this page, clicking a link or continuing to browse otherwise, you agree to the use of cookies.
On the 12mm my MHB must have a typo because it says the tolerance is +43 -0. I'm using a book published by FAG Bearings that lists the complete tolerance range for each designation, I don't have iso 2768 mk pdf Machinerys Handbook here to check and see what is in there. I'm using a book published by FAG Bearings that lists the complete tolerance range for each designation, I don't have my Machinerys Handbook here to check and see what is in there. MBensema, Thank you for that link, it doesnt offer everything I need but it does come closer than I had gotten by myself. I didnt think that correct for a shaft but that is what is in my book. Your help at least lets me know where I was right and where I need to work a little harder. I just need to find a better source and I am hoping to not have to buy all the standards if I dont have too. I do have a shaft dimention that is not on the chart, it is for an OD 12mm h9. This link often gets put up with questions about ISO tolerance. This link often gets put up with questions about ISO tolerance.
